Thursday, December 18, 2008

DIY Ultrasonic Cleaner

--discussion of this project has moved to my main site: http://www.obnauticus.com-- From cleaning car parts to cleaning cleaning jewelry, ultrasonic cleaners are used in a wide variety of applications. Wither it's a sensitive diamond ring that needs a little polish, or an old spark plug covered in grease -- Ultrasonics are the most popular method of choice for cleaning parts in little time with precision.

How Ultrasonic Cleaning works:

Ultrasonic cleaning works by tearing voids between particles in the cleaning solution, this is called cavitation. These little pockets of air explode when they come in contact with a solid surface. Some people report these explosions occurring at pressures up to 15,000PSI and temperatures up to 5,000K. Although these conditions are extreme, the pockets of air are so small that they only have enough power to tear off any surface dirt on the dirty object. You can even stick your hand in the ultrasonic cleaner while it is running.

However, like all other things; machines with this amount of precision cost a large sum of money. This De-I-Why article is written to help you design your own Ultrasonic cleaner at a fraction of the price.

This project is similar to all audio setups. Previous knowledge of audio hardware and setup is a real plus, and will help you lots with the design of this project.
Materials:

* = Hard to find around the house.
  1. Oscilloscope (Nice if you have one, but not necessary).
  2. * Two Ultrasonic Transducers
  3. * A capable sound card (with a frequency response ≥the optimal resonating frequency for the transducers), or function generator (same restrictions apply).
  4. * Linear Amplifier (with an RMS > the n*the required power necessary to drive the transducers (e.g. 2 Transducers need to be driven at 55W (2x55Watts) -- therefore I need an amplifier with an RMS ≥110Watts) ). The amplifier's frequency response must be greater than or equal to the frequency necessary to drive your transducers.
  5. A soldering iron
  6. Solder
  7. Old RCA Audio cables.
  8. A stainless steel container capable of holding a cleaning solution (Jelly roll, or cookie tray will do as long as it is built with only one layer of steel).
Note: Items 3 and 4 can be replaced by buying an "Ultrasonic Generator," however, they are generally very expensive, and do not have enough output power to drive more than one transducer.

Gathering the hard-to-find Materials:

1. Ultrasonic Transducers:
  • Ultrasonic Transducers are very easy to find online, I got mine from eBay, a couple of 55Watt ones. Make sure the ones you get are designed for cleaner applications.


2. A capable soundcard:
  • My sound is the X-Fi Fatal1ty, I generated a high-frequency (44kHz) waveform within Adobe Audition and verified it was 44kHz on my oscilloscope to make sure it was able to drive the transducers. Check your manufacture's specifications for your sound card's frequency response or maximum sampling rate to find out what the maximum output frequency of your soundcard is.
3. A linear amplifier:
  • Make sure the RMS of the power is equal to or greater than the total amount of power needed to drive your transducers (the sum of the power necessary to drive all of your transducers must be equal to or greater than the RMS of the power your amplifier provides).
  • You must also make sure the frequency response of the amplifier is greater than or equal to the frequency which you plan to run your transducers at (usually around 40-46kHz).

  • I chose to use the Pyle Pro PT-2000 because it provides 175W of RMS power over two channels with a frequency response of 10Hz to 50kHz. This amplifier both meets and exceeds the specs required to drive the transducers I picked. It is also relativly cheap.
  • Note: Do not buy an "Ultrasonic Amplifier," these are just regular audio amplifiers. There is a particular seller on ebay which has photoshopped a Pyramid Pro 150W amplifier and charges about 40% more just reselling it on eBay under a different name.
4. A soldering Iron:
  • If you don't already have one you need to get one. A tempreature controlled one is nice, but not necessary.
  • I used my Weller WESD51, this soldering iron is nice for everything and is a popular choice among many hobbyists as well as professionals.
5. A Stainless Steel Container:
  • Keep in mind that it will be filled with a cleaning solution, and therefore must be able to hold a cleaning solution.
  • The container must be made of a something capable of resonating sound waves. It's also a good idea to look for corrosion resistant material. Stainless steel is the most popular choice in the world of ultrasonic cleaning.
  • Make sure there is only one layer of metal between the stainless steel and the cleaning solution.
  • I chose to use a Jelly Roll pan, there are obviously more choices out there. Be creative!
Procedure:
  1. Epoxy your ultrasonic transducers to the bottom of your stainless steel container. Make sure they are in locations which allows cavitation to occur evenly throughout the cleaning tank. I suggest spacing them diagonally from each other in a rectangular cleaning tank, so there is even cavitation throughout the entire volume of the cleaning tank. Make sure when epoxying them to the bottom that you try to keep the bond space between the transducers and the steel tank as small as possible. You can use vice grips or weights placed on top of the transducers to achieve this.

  2. Now, cut off one end of an old RCA cable of your choice. Next, solder both of the wires (doesn't matter which one), to ONE of the pads in the picture, pointed out by red arrows. Do not solder both wires to one pad, solder one wire per pad, and solder both of them to a pad.


  3. Repeat step 2 for the other transducer.
  4. Next, plug the other end of the component cables into the output of your amplifier (left or right channels do not matter).
  5. Next, plug your sound card (or HF sin wave generator) into the input of your amplifier.
  6. Now, fill the stainless steel container with a cleaning solution of your choice (I used Isopropyl Alcohol "iso alcohol," most people do not suggest using flammable materials because there is a chance it will explode, I didn't really care though).
  7. Make sure everything is hooked up correctly.
  8. Turn your amplifier on, and generate your HF sin wave (you can find some sound card wave generators on google, I used Adobe Audition).
  9. If that did not explode, then you should be seeing cavitation in the cleaning solution.
Conclusion:

This should work for most cleaning applications, I have seen many people use Ultrasonic cleaning for cleaning grease off of old PCB's, a well as a variety of different parts. Just make sure to change your cleaning solution out once you feel it has been tainted with whatever dirt you may have put into the cleaner.

20 comments:

  1. Good instructions. A simple oscillator can be made using the LM555 or NE555 (or a ny of the variants) and I would use a power mosfet or such as an amplifier if any is necessary from the output.

    ReplyDelete
  2. Eventually someone took the "black magic" from ultrasonic cleaners...good job!

    ReplyDelete
  3. If you're capable of some simple electronics design you could make a simple inverter using MOSFETs and a resonant output stage to drive the transducers. This requires the system to always operate at one frequency (you must then also fill with the same volume of fluid and same density or adjust to match) but would allow very high operating efficiency. Operating audio amplifiers at 40+KHz continuously at high power is a risk as most aren't designed to do that.

    ReplyDelete
  4. great job, i like your blog, im DIYers to
    i want to build one and write it at my blog,

    thanks,...

    ReplyDelete
  5. do you have pics of the final results?

    ReplyDelete
  6. This comment has been removed by the author.

    ReplyDelete
  7. Great article. Anybody tried so far making it? Also confirm if the amplifier was able to do some prolonged running for cleaning applications.

    ReplyDelete
  8. "I generated a high-frequency (44kHz) waveform within Adobe Audition and verified it was 44kHz on my oscilloscope to make sure it was able to drive the transducers. Check your manufacture's specifications for your sound card's frequency response or maximum sampling rate to find out what the maximum output frequency of your soundcard is."

    This is very vague. Does this mean the soundcard has to be in the computer? Does this mean your cleaner is not a stand alone device but has to be run everytime from the computer?

    ReplyDelete
  9. Just an idea if you could get a 40kHz signal recorded on a CD or mp3 and use an mp3 player or some sort of portable device to play the sound vs a computer that might make the unit more portable?

    ReplyDelete
  10. Nm talked to an audio friend of mine and he said no go on the mp3/CD stuff.

    ReplyDelete
  11. I have a Sound Card from a computer will that work? How does the sound card connect into the amplifier? Is there any input into the sound card? Does the sound card require any power if so AC or DC? If I sound like a goof it's because I am on this subject. I'm trying to build one to clean carburators. Thanks for any help.

    ReplyDelete
  12. You can download signal generators for Androids and iPhones.
    For Android, there are two free generators: "Signal Generator" and "Soundform".
    The signal is autorepeating.
    I got the transducers in the mail today, and am going to try it out.

    ReplyDelete
    Replies
    1. Hi, struggling to find the correct transconducers on Ebay and online. If you have a link, it what help immensely.

      Delete
  13. i do not think that computer soundcards can reproduce frequency higher than 22 khz, which is the highest frequency humans can hear. i think this applies also to mp3 players and / or to normal amplifiers; it would be pointless for a computer to be able to generate sounds that nobody can hear. one should check the soundcards specs before anything else.

    ReplyDelete
  14. Hi Ob! I tried this and the transducer i got was the flat one. Unfortunately it only emmits the sound but does not vibrate. Which one is better? - the one you showed in your post or the piezo type which is triangular and bulky? My application would be to clean engine parts and the block in a 45-55 gallon container? How many of the transducers would i need for that size of a setup? Tia!

    ReplyDelete
  15. Flexi pack offers a full line of critical cleaning detergents for a wide range of metal cleaning applications. Our products make cleaning metal surfaces fast and easy, saving time and money in the process. Service to the industry, precision formulation, quality control, and excellent technical services are the benchmarks of Flexi pack.
    Metal Cleaning Solutions

    ReplyDelete
  16. Business Links has been a leader in Metal cleaning solutions. Our solutions are used in a number of industries for a wide range of applications as well as cleaning stainless steel and other metal surfaces. We offer safe and efficient cleaners backed by excellent technical support and information.
    Metal Cleaning Solutions

    ReplyDelete
  17. How much of the kit you mention above is covered by this item on ebay? http://www.ebay.co.uk/itm/40KHz-50W-Watt-Ultrasonic-Cleane-Transducer-Power-Drive-Module-220V-/160754562847?hash=item256db7f71f:g:jtIAAOSwBahVLytO

    ReplyDelete
  18. buying
    wholesale liquidation pallets at Takeitbythepallet and resell on ebay is a good business this year

    ReplyDelete